SEE ALSO THE CB EQUIPMENT PAGE.
CLICK ON ANY IMAGE TO SEE A HIGHER RESOLUTION PICTURE
This robust power supply has been specifically
designed for use in Radio Communication systems.
It is rated at 25 Amps continuous and 50 Amps
intermittent use. It incorporates separate Volt and Ampere meters which
are also illuminated.
Mains input: 220 V AC ±10% 50 Hz
Output:
4 to 18 Volts DC
Load:
25A continuous, 50A intermittent
Stability:
1% from no load to full load
Ripple:
5mV pp
Dimensions: 320 x 330 x 160 mm
Weight:
17.5 Kg.
See also other Power Supplies for a more comprehensive range.
OVP16 - OVER VOLTAGE PROTECTION
This little device can save your 12 volt operated
equipment from total loss ! The OVP16 is inserted between the
supply (battery, power supply etc.) and the equipment. If the voltage
exceeds 15 - 16 volts it will disconnect the equipment from the supply
to prevent damages.
LD7 - LIGHTNING PROTECTOR
+ AC MAINS FILTER
A lightning protector and AC mains RF
filter in one small package measuring
165 x 90 x 60 mm and weighing
just 0.9Kgs.
Mains input voltage 110 to 220 V AC 50 Hz with a maximum load of
7 Amps.
A low cost yet reliable 7 digit LED display
frequency counter. Operates from 0.3 to 50 MHz with a sensitivity of better
than 50mV.
Power requirements: 12 - 14V DC at 150mA
Dimensions:
125 x 170 x 35 mm
Weight:
0.86Kg
Frequency: 3 to 200 MHz
Impedance: 50 Ohm
Max. Power: 1KW SSB
Dimensions: 135 x 45 x 50 mm
Weight:
0.24Kg
HP202 - DIRECT READING SWR + POWER METER
A very handy instrument that gives direct forward and reflected power PLUS SWR without the need for any calculations or settings.
Frequency: 26 to 30 MHz
Impedance: 50 Ohm
Max. Power: 1KW SSB
Accuracy: ±10%
Dimensions: 130 x 140 x 80 mm
Weight:
0.65Kg
TM999 - SWR METER + ATU
Frequency: 26 to 30 MHz TM535 - DIRECT READING SWR + POWER METER + ATU
A very versatile instrument suitable for Amateur
and CB stations. Gives direct forward and reflected power PLUS SWR without
the need for any calculations or settings.
Frequency:
1.6 to 30 MHz
M27 - ANTENNA MATCHER
Frequency:
26 to 28 MHz Compact power reducer with 2 switchable levels
of attenuation: 25% or 50%
Frequency:
0 to 30 MHz
HP6 - POWER REDUCER
The HP6 power reducer incorporates electronic
switching for transmit/receive modes. It has 6 selectable attenuation levels
up to 90% and has a large power meter calibrated in Watts. Frequency:
0 to 30 MHz
With AM illumination modulation indicator
HP29 - PRE-AMPLIFIER
With AM modulation meter in percentage. Frequency:
26 to 30 Mhz
P27-1 - PRE-AMPLIFIER
Frequency:
26 to 30 Mhz P27M - PRE-AMPLIFIER
Frequency:
26 to 30 Mhz A very small unit which suppresses those nasty
harmonics and eliminates TV interference.
Dimensions: 40 x 85 x 30 mm
DX145 - AERIAL SPLITTER
Dimensions: 40 x 85 x 30 mm
This unit is designed to operate and
match two aerials to one transceiver.
Frequency:
2 to 30 Mhz
Frequency: 0
to 30 Mhz
Frequency: 0
to 30 Mhz
Power requirements: 10 - 14V DC
MB+4 MICROPHONE
Impedance:
0 - 5K Ohm
MB+9 MICROPHONE + ECHO + ROGER BEEP
Impedance:
0 - 5K Ohm
M93 - PRE
A palm-held microphone with integral pre-amplifier
and special circuitry providing a particularly penetrating and clear
modulation. A modulation level control is located on the front. The microphone
is powered by a standard PP3 9 Volt battery and comes fitted with a robust
but flexible spiral lead, terminated in a 4 pole connector with standard
connections which will fit most standard two-way radios.
M95 - PRE + ROGER BEEP
M93 - PRE + ECHO
M99 - PRE + ROGER BEEP + ECHO
This microphone has a unique circuitry which
allows the alteration of your voice ! The six way switch on the front allows
you to change your voice into that of the opposite sex making you unrecognizable
to the listener. It can also be adjusted to produce funny sounds like Donald
Duck whilst remaining very clear and sharp. A switch also allows
the switching off of the voice changer turning the M101 into an excellent
pre-amplified microphone. It is also fitted with an earphone jack so that
the output of the microphone is monitored.
We also carry a vast range of aerials for hand-held portables, mobile
or base use and a range of accessories and fittings to meet all requirements. ©ALL MATERIAL IS PROTECTED BY COPYRIGHT LAWS AND MAY NOT BE REPRODUCED IN ANY FORM WHATSOEVER WITHOUT THE PRIOR WRITTEN CONSENT OF THE WEBMASTER.
Max. Power: 100 Watts SSB
Accuracy: ±5%
Dimensions: 160 x 100 x 60 mm
Weight:
0.65Kg
Max. Power:
500 Watts
Input Impedance: 50 Ohm
Output Impedance:
10 - 500 Ohm unbalanced
or 100 - 3000 Ohm balanced
Dimensions:
270 x 210 x 90 mm
Weight:
2.7Kg
Frequency:
26 to 28 MHz
Max. Power:
100 Watts AM
Input Impedance: 50 Ohm
Insertion loss:
0.2dB
Dimensions:
105 x 45 x 43 mm
Weight:
0.2Kg
Max. Power:
500 Watts AM
Input Impedance: 50 Ohm
Insertion loss:
0.2dB
Dimensions:
160 x 80 x 120 mm
Weight:
0.8Kg
Max. Power:
25 Watts AM
Dimensions:
60 x 85 x 40 mm
Weight:
0.2Kg
Max. Power:
10 Watts AM
Dimensions:
130 x 140 x 80 mm
Weight:
0.75Kg
Frequency:
26 to 30 Mhz
Gain:
-10 to 25dB fully adjustable
Power requirements: 10 - 15V DC at 100mA
Tx. Insertion loss: 0.2dB
Max. Power:
15 Watts AM
Dimensions:
130 x 130 x 80 mm
Weight:
0.6Kg
Gain:
-10 to 25dB fully adjustable
Power requirements: 10 - 15V DC at 100mA
Tx. Insertion loss: 0.2dB
Max. Power:
15 Watts AM
Dimensions:
130 x 130 x 80 mm
Weight:
0.6Kg
Gain:
25dB fully adjustable
Power requirements: 10 - 15V DC at 100mA
Tx. Insertion loss: 0.2dB
Max. Power:
15 Watts AM
Dimensions:
160 x 120 x 50 mm
Weight:
0.55Kg
Gain:
25dB fully adjustable
Power requirements: 10 - 15V DC at 100mA
Tx. Insertion loss: 0.2dB
Max. Power:
15 Watts AM
Dimensions:
45 x 45 x 110 mm
Weight:
0.22Kg
Frequency:
0 to 30 MHz
Max. Power:
300 Watts
Insertion loss:
0.25dB
Dimensions:
110 x 33 x 50 mm
Weight:
0.22Kg
A small pre-wired unit which will allow the
use of the CB antenna as a car radio antenna simultaneously. Will withstand
power inputs up to 100 Watts with little or no insertion loss. NO power
connection required.
Weight:
0.22Kg
This unit will allow the use of a VHF antenna
as a car radio antenna simultaneously. Will withstand power inputs up to
100 Watts with little or no insertion loss. NO power connection required.
Weight:
0.22Kg
Max. Power:
200 Watts
Dimensions:
60 x 100 x 35 mm
Weight:
0.22Kg
Impedance: 50 Ohm
Max. Power: 500 Watts AM
Insertion loss: 0.2dB @ 50 MHz
Dimensions: 105 x 60 x 38
mm
Weight:
0.2Kg
Incorporates an over voltage anti-static device.
Impedance: 50 Ohm
Max. Power: 500 Watts AM
Insertion loss: 0.2dB @ 50 MHz
Dimensions: 105 x 100 x
38 mm
Weight:
0.35Kg
Incorporates an over voltage anti-static device.
A high definition echo effect. Adjustable
echo level and repetition.
Dimensions:
105 x 105 x 35 mm
Weight:
0.4Kg
High quality desk top ceramic cartridge
microphone
Frequency:
250 - 3500 Hz
Max. output level: -23dB
Power:
9V standard PP3 battery
Dimensions:
95 x 160 x 230 mm
Weight:
1.05Kg
High quality desk top ceramic cartridge microphone
with adjustable echo, "roger beep" and VU meter.
Frequency:
250 - 3500 Hz
Max. output level: -23dB
Power:
9V standard PP3 battery
Dimensions:
95 x 160 x 230 mm
Weight:
1.1Kg
A palm-held microphone with integral pre-amplifier
and special circuitry providing a particularly penetrating and clear
modulation. A modulation level control is located on the front as is the
on-off switch of the "Roger Beep". The circuitry of the "Roger Beep"
is bitonal and pleasant to the ear. The microphone is powered by a standard
PP3 9 Volt battery and comes fitted with a robust but flexible spiral lead,
terminated in a 4 pole connector with standard connections which will fit
most standard two-way radios.
A palm-held microphone with integral pre-amplifier
and high quality ECHO circuitry. The echo circuitry uses a special
design in order to give excellent results, unrivalled by any other microphone.
The pre-amplifier and echo repetition adjustments are housed inside the
body of the microphone whilst the echo level adjustment is located on
the front. The microphone is powered by a standard PP3 9 Volt battery and
comes fitted with a robust but flexible spiral lead, terminated in a 4
pole connector with standard connections which will fit most standard two-way
radios.
A palm-held microphone with integral pre-amplifier
and high quality ECHO circuitry. The echo circuitry uses a special
design in order to give excellent results, unrivalled by any other microphone.
The pre-amplifier and echo repetition adjustments are housed inside the
body of the microphone whilst the echo level adjustment is located on
the front together with the on/off "Roger Beep" switch. The microphone
is powered by a standard PP3 9 Volt battery and comes fitted with a robust
but flexible spiral lead, terminated in a 4 pole connector with standard
connections which will fit most standard two-way radios.
AERIALS & ACCESSORIES
18-20, MSIDA ROAD,
GZIRA. GZR 1401.
MALTA.
TELEPHONE: (0356) 2131 3283 or 2132 0845
FAX: (0356) 2133 8087
E-MAIL CONTACT
sales@fabian.com.mt
