Rewireable cable sockets manufactured to comply with CE, UL, CSA, VDE, BS and SEMKO approvals. Fitted with internal screw connections (available also in solder type) and cable strain relief.
Available in straight or angled formats for 250V AC with contact ratings of 6, 10 or 16A.
Colours: Black, White, Ivory, Grey.
Rewireable cable plugs manufactured to comply with CE, UL, CSA, VDE, BS and SEMKO approvals. Fitted with internal screw connections (available also in solder type) and cable strain relief.
Available in straight or angled formats for 250V AC with contact ratings of 6, 10 or 16A.
Colours: Black, White, Ivory, Grey.
A range of front or rear mounting inlet connectors approved to IEC320
and CEE22. Available for screw mounting or "press-fit" with
either 4.8mm or 6.3mm (¼") connections. These connectors have all
major approvals, including UL, CSA, VDE, SEV, SEMKO, DEMKO, NEMKO etc.
A rear insulating boot is also available.
10A rated at 250V AC.
A female version of the chassis plug, normally used for power take-off
applications. Available for screw mounting or "press-fit" with
either 4.8mm or 6.3mm (¼") connections. These connectors have all
major approvals, including UL, CSA, VDE, SEV, SEMKO, DEMKO, NEMKO etc.
A rear insulating boot is also available.
10A rated at 250V AC.
A non-rewirable straight plug moulded to a 2M length of 3 core 0.75mm
cable. Sheated overall in black or grey. Rated at 10A 250V
AC. ASTA approved to BS4491 and IEC320. Cable approved to BS6500. (*)
A non-rewirable straight socket moulded to a 2M length of 3 core 0.75mm cable. Sheated overall in black or grey. Rated at 10A 250V AC. ASTA approved to BS4491 and IEC320. Cable approved to BS6500. (*)
(*) Both
above plugs and sockets are high quality mains power cords for a
wide range of applications. Plugs tops and connectors are ultrasonically
welded to ensure an extremely strong bond. The cord protection sleeve
is moulded to the cable and ribbed for greater flexibility.
ALL cords are 100% electrically and mechanically inspected
and ASTA approved to BS1363/A.
IEC 320 Reverse Configuration
Moulded Lead Set
Straight and angled moulded plugs available with unterminated leads
in different lengths. Rating 250V a.c. 6, 10 or 16A
Moulded plug and socket cable assemblies
Moulded plug and socket cable assemblies consisting of either straight
or right angle CEE22/BS 4491 10A sockets with integral lead in black, white
or grey, terminated with moulded BS 1363/A 13A square sleeved pin mains
plugs fused at 13A. Fully tested and approved by ASTA. Rated at 250V a.c.,
10A max. Cable: 3-core 1·0mm2 PVC to BS 6500 (1975). BASEC approved.
Available in 2 and 3 metre lengths.
IEC Inlet plugs with integral mains filter.
Designed to filter mains
borne interference where capacitors alone may prove inadequate. Connection
by 250 (¼") receptacles.
This IEC mains lead consists of a 3-pin C.E.E.22 shrouded plug and socket on either end of 2 metres of 3-core BASEC approved cable. Rated 250V a.c./10A max. Black PVC mouldings and cable sheath. Kite marked and BEAB approved.
Available with straight or right angled IEC connectors
Insulating boots for the chassis mounting plugs and sockets
in moulded PVC designed to insulate and protect the connections.
©ALL MATERIAL IS PROTECTED BY COPYRIGHT LAWS AND MAY NOT BE REPRODUCED IN ANY FORM WHATSOEVER WITHOUT THE PRIOR WRITTEN CONSENT OF THE WEBMASTER.
